Page 1 of 2

My new q2 2.0 tdi 190

Posted: Thu Aug 03, 2017 7:25 pm
by Digital67
Hello guys
Who can explain how to disassemble the q2's center console?
Thank you so much

Re: My new q2 2.0 tdi 190

Posted: Fri Aug 11, 2017 11:41 am
by IanQ2
Usual method is to start by removing the gear gaiter, then pull up the large part which the gear gaiter and mmi unit is in up and there is likely torx screws under to secure. You will also have to pull the rear section of the centre console off and there will be torx or bolts at the back. I also think there is a torx screw in the side right near the dash

I have ETKA (Audi's parts catalogue) diagram of the parts but cant host as for some reason my photobucket has gone wrong.

Re: My new q2 2.0 tdi 190

Posted: Sun Dec 01, 2019 7:11 pm
by apadilc1
IanQ2 wrote:
Fri Aug 11, 2017 11:41 am
Usual method is to start by removing the gear gaiter, then pull up the large part which the gear gaiter and mmi unit is in up and there is likely torx screws under to secure. You will also have to pull the rear section of the centre console off and there will be torx or bolts at the back. I also think there is a torx screw in the side right near the dash

I have ETKA (Audi's parts catalogue) diagram of the parts but cant host as for some reason my photobucket has gone wrong.
Can you share your diagram? I want to Vinyl wrap my Center console

Re: My new q2 2.0 tdi 190

Posted: Mon Dec 02, 2019 10:27 am
by IanQ2
This should help

Re: My new q2 2.0 tdi 190

Posted: Sun Dec 08, 2019 7:08 am
by apadilc1
IanQ2 you are wonderfull

Re: My new q2 2.0 tdi 190

Posted: Mon Feb 10, 2020 10:09 pm
by brookead
I don't suppose anyone knows the part number for the white led backlit 12v power socket in the Q2/A3 do they? I just finished running the power to the rear console and I have a temporary (read: cheap and nasty looking) 12v power socket installed but I would REALLY like to install the nice backlit one (I ran the backlight cable at the same time as the other 2, just need something to connect it to!

I've looked in EKTA and I can SORT of find something. Looks like it comes in 2 parts. the container (with or without backlighting) and the socket itself. The problem is all the sockets "with lighting" are listed as up until 2013 only. The part number from 2013 onwards doesn't list itself as being backlit whether I take the front or rear unit.

Since I am retrofitting this myself I don't care what model it comes from and whether it was intended for the front or the back, as long as it's a flush mount 12V power sock with a white led backlight. But I am struggling to find the right parts!

Any assistance much appreciated.

Thanks

Tony

Re: My new q2 2.0 tdi 190

Posted: Tue Feb 11, 2020 10:24 am
by IanQ2
Hi Tony

The part number for the Q2 12v socket is 4M0919309C

Its on diagram 919-090 on ETKA for reference.

Couple for sale on ebay from Lithuania or the usual sources of TPS or Audi.

Get some pics up of your install once done, sounds a nice retrofit

Re: My new q2 2.0 tdi 190

Posted: Tue Feb 11, 2020 8:23 pm
by brookead
Will do, thanks Ian.

So if that's the part number for the actual power outlet, would the LED backlit part be 8V0 919 340?

Re: My new q2 2.0 tdi 190

Posted: Wed Feb 12, 2020 1:53 am
by brookead
Never mind. Figured it out. Ordered one from Lithuania and will post a picture when I have it installed, along with the one in the boot and my Audi Beam install. :)

Re: My new q2 2.0 tdi 190

Posted: Sun Feb 16, 2020 7:30 pm
by apadilc1
I can not remove the gear gaiter neither the MMI controls, I want to vinyl wrap the large part around them. I pull, but it feels something will break. 😭 Someone has a video?